[SoundStage!]Home Audio
Equipment Measurements

December 2003

Blue Circle Audio BC28 Stereo Amplifier: Measurements

All amplifier measurements are performed independently by BHK Labs. Please click to learn more about how we test amplifiers there. All measurement data and graphical information displayed below are the property of SoundStage! and Schneider Publishing Inc. Reproduction in any format is not permitted.

Additional Data
  • Measurements were made with 120V AC line voltage.
  • Power output and distortion plotted with both channels driven.
  • Gain: 19.2x, 25.7dB.
  • Output noise, 8-ohm load, unbalanced input, 1k-ohm input termination: wideband 0.363mV, -77.8dBW; A weighted 0.054mV, -94.4dBW.
  • AC line current draw at idle: 0.72A.
  • Output impedance at 50Hz: 0.16 ohms.
  • This amplifier does not invert polarity.  
Measurements Summary

Power output with 1kHz test signal

  • 8-ohm load at 1% THD: 127W

  • 4-ohm load at 1% THD: 219W

General

The Blue Circle BC28 is a hybrid design utilizing a twin-triode tube for the front end and a solid-state output stage. This output stage is most unusual in that it utilizes four TO-3 transistor-sized devices with four-pin connections in addition to the case for each of these devices. These are most likely some kind of power op amp. It appears that there are two parallel banks of two of these devices for each output channel. Further, the interconnection of these devices produces a bridged output signal with two phases of opposite polarity in respect to signal ground from the single-ended drive out of the tube front end.

Chart 1 shows the frequency response of the amp with varying loads. As can be seen, this unit has a very high frequency rise in response, most likely leading to a peak in the response beyond the 200kHz limit of the chart. Also seen is a reasonably low output impedance, as evidenced by the close spacing between the open circuit and loaded curves. The variation in response with the NHT dummy speaker load is of the order of +0.1dB,-0.15dB -- close to being audibly inconsequential. Chart 2 illustrates how total harmonic distortion plus noise versus power varies for 1kHz and SMPTE IM test signals and amplifier output load. As can be seen, attainable power is greater for the 4-ohm load as is usual for most power amplifiers. Total harmonic distortion plus noise as a function of frequency at several different power levels is plotted in Chart 3. Of note is the very rare but desirable characteristic of almost perfect constant amount of distortion as a function of frequency. Damping factor versus frequency is shown in Chart 4. As with the harmonic distortion versus frequency, this damping factor is quite constant with frequency. A spectrum of the harmonic distortion and noise residue is plotted in Chart 5 for a 10W 1kHz signal into a 4-ohm load. With 8-ohm loading at the 10W level, the distortion spectrum is more complex and with a higher amount of higher harmonics past the second harmonic. Although the overall hum level is quite low for this amp, the AC line harmonic series is fairly complex containing both even and odd harmonics of the 60Hz line frequency.

Chart 1 - Frequency Response of Output Voltage as a Function of Output Loading


Magenta line: open circuit
Red line: 8-ohm load
Blue line: 4-ohm load
Cyan line: NHT dummy-speaker load

Chart 2 - Distortion as a Function of Power Output and Output Loading


(line up at 50W to determine lines)
Top line: 8-ohm SMPTE IM
Second line: 4-ohm SMPTE IM
Third line: 8-ohm THD+N
Bottom line: 4-ohm THD+N

Chart 3 - Distortion as a Function of Power Output and Frequency


4-ohm output loading
Cyan line: 200W
Blue line: 60W
Magenta line: 10W
Red line: 1W

Chart 4 - Damping Factor as a Function of Frequency


Damping factor = output impedance divided into 8

Chart 5 - Distortion and Noise Spectrum


1kHz signal at 10W into an 4-ohm load

 

[SoundStage!]All Contents
Copyright © 2003 Schneider Publishing Inc.
All Rights Reserved